Refrigerator Door Gasket –Appliance Repairs in Port Elizabeth
Refrigerator Door Gaskets becomes brittle overtime and a good sealing Fridge Door Seal is needed for effective cooling and to stop warm air leaking into the refrigerator Cabinet.
Signs of defected door seal;
• Build up of ice along the edges of your Freezer
• Excessive water moister inside the Fridge cabinet
• Smelly food
• Food that go off quicker before expiring date
The door seal keeps the wet (moist) or warm air out of the refrigerator and keep the cold air sealed inside the refrigerator.
Replacing your Fridge door seal can be done by yourself all you need is a couple of point from me
There are three basic types of refrigerator door gaskets/seals;
1. Push on type
2. Clip-on Type
3. Flat-back type
They also come in different profiles and colors (White, Grey, Cream and Brown).
Push On Type Refrigerator Door Gasket
To remove the (tong and groove type) seal start at the top right hand corner. Just lift it out by puling on the old refrigerator seal - slowly pull it out of the channel groove. Then Work your way down the sides and at the end pull it out of the bottom channel.
Start inserting the new gasket at the top corner and work your way over to the other top corner. Then you move down the sides to the bottom corners - slowly push the seal in the channel with your thumb.
If you lift the seal-lip away from the inner plastic of the door panel your will see screw underneath the door gasket that holds the Gasket in place.
Look if there is a little bulge along the rim of the plastic, this indicates that your refrigerator uses a clip-on refrigerator Gasket.
Otherwise was if the plastic door panel are just smooth (with screws to hold it in place) it will take a flat-back Door gasket. The flat-back gasket normally gets used on older refrigerator and deep-freezers.
If there are no screws present underneath the door gasket and it looks like the gasket is molded into the door it means the gasket is a push-on-type.
Fitting the Clip-on Type Door Seal
Always start by unscrewing the bottom door panel screws and work you way around the panel to the top. Then when you have removed all the side screw you take unscrew the top screw. The plastic panel and gasket should now be loose from the refrigerator. If the panel is still molded to the door just un-clip the gasket and refit the new gasket.
Flat back Door gasket
The procedure is same as with the clip-on type
• When fitting the screws back, put one screw at the top to hold the panel in place.
Start inserting the screws form the bottom working you ways around the sides to the top.
While doing this Do Not tighten the screw - align the door gasket first .
Only once your stand back and see that the new door seal is straight and flush
Then start tightening the screws - again from the bottom up.
• If the new flat-back seal do not have pre-manufactured holes in the gasket - just press the screws into the seal threw into the door holes. By attempting to make holes before fitting the gasket, can really turn into timely exercise.
• If the seal is molded into the door panel and there are no screws present, save yourself and call a professional because it means the seal will have to be cut to fit the new seal.
How to order a new door Gasket
The Clip-on and Flat-back type gasket can be made according to you specifications. Just Measure the gasket from one end to the other and top to bottom (length). You will also need to specify the profile and color.
Order the Tong and Groove-type only from the unit manufacture or their service agents only, because the lip and the groove can be ever so slightly different when you have this made up and a simple procedure will now turn into a night mare - just trust me on this one.
To order from the manufacture or their service agent you will need to provide them with your refrigerator model number and sometimes also the type number. These numbers can be found on the back or on the sides of the fridge. Sometimes it is even situated behind the vegetable draws inside the fridge cabinet.
To preserve the life of a Gasket clean it regularly with a mild soap (Handy Andy- ammonia is to powerful)
Put some Vaseline of Glycerin along the cabinet side where the door hinges are –it will make the door closes smoother.
As always if you run into a snags or you need more pointers just go to High Point for more free advice.
Enjoy your repair project.